AI-GPS-W-M2-FLP

Flameproof GPS Master and Slave Clocks

No items found.
Flameproof GPS master clock, AI-GPS-W-M2-FLP
Flameproof GPS Clocks

Flameproof GPS Master and Slave Clocks

One time for every hazardous area. Flameproof LED clocks that take their time from a GPS master and pass it to every slave, in enclosures certified by CIMFR for Gas Group Areas I, II, IIA, and IIB.

CIMFR Certified Enclosure GPS Time Wired RS-485 Wireless RF Ethernet with PoE
500 msGPS time accuracy at the master
CIMFRCertified flameproof enclosure
255 slavesPer master on a wireless RF mesh
1.2 kmSlave range from the master
Product Overview

In a classified area, an ordinary clock cannot go on the wall. These can.

In a plant with flammable gases or vapors, an ordinary clock cannot go on the wall. These flameproof GPS clocks can. The master clock takes the satellite time of the country of use, accurate to 500 milliseconds, and passes it to slave clocks over wired RS-485, wireless RF, or Ethernet TCP/IP. Every clock in the network shows the same time, and nobody has to reset them by hand.

The enclosures are certified by CIMFR, Dhanbad, for Gas Group Areas I, II, IIA, and IIB. The standard 2.5 inch series has three models: the AI-GPS-W-M2-FLP master clock, the AI-CL2-S-FLP slave clock for hours, minutes, and seconds, and the AI-CL2-S1-FLP slave clock for hours and minutes. We customize the clocks to your requirements, with a 2.5 inch or 4 inch display, and with date and time format available.

How It Works

Receive, relay, display

The master clock receives satellite time through an active GPS antenna, and it distributes that time to the slave clocks over the communication option you choose. Slave clocks show what the master sends, so the whole network shows the same time to the second. If power fails or communication drops, an internal memory battery keeps the real time clock running, and the slaves carry on in a high accuracy mode until synchronization returns.

15:22:35MASTER
15:22:35SLAVE
15:22SLAVE

Every clock in the network shows the same time, in HH:MM:SS or HH:MM.

When the GPS Signal or Power Drops

The clocks keep running

An internal memory battery keeps the real time clock running through power cuts. If RS-485 or wireless RF communication fails, the slave clocks run in a high accuracy mode with an annual drift of not more than ±120 seconds, or 2 minutes. Without a GPS signal, the standalone accuracy is also ±120 seconds per year. Time can be reset from the keypad on the circuit board inside the box, or with the optional wireless remote control. Normal synchronization resumes when the signal or the communication returns.

±120 sNO GPS SIGNAL
±120 sNETWORK DOWN

Drift of not more than ±120 seconds, or 2 minutes, per year.

Network Layout

One master, up to 255 slave clocks on a wireless mesh

With wireless RF, the clocks work in a mesh network at 865 MHz. Slave clocks can be up to 1.2 kilometers from the master and still show the same time as the master.

Wireless RF mesh topology. The master clock takes satellite time through its GPS antenna, and the slave clocks follow it.
The Models

Flameproof master and slave clocks in the 2.5 inch series

Flameproof GPS master clock

AI-GPS-W-M2-FLP

6 digit, 2.5 inch, 7 segment super bright red LED display. It takes GPS time through its active antenna and passes it to the slave clocks.

Display
6 digit, 2.5 inch
Time format
HH:MM:SS
Body (W x H x D)
460 x 260 x 120 mm
Flameproof slave clock

AI-CL2-S-FLP

6 digit, 2.5 inch, 7 segment super bright red LED display. It shows hours, minutes, and seconds, the same as the master.

Display
6 digit, 2.5 inch
Time format
HH:MM:SS
Body (W x H x D)
460 x 260 x 120 mm
Flameproof slave clock

AI-CL2-S1-FLP

4 digit, 2.5 inch, 7 segment super bright red LED display. It shows hours and minutes for a simpler face.

Display
4 digit, 2.5 inch
Time format
HH:MM
Body (W x H x D)
340 x 170 x 90 mm
ModelRoleDisplayTime format
AI-GPS-W-M2-FLPFlameproof GPS master clock6 digit, 2.5 inch, 7 segment super bright red LEDHH:MM:SS
AI-CL2-S-FLPFlameproof slave clock6 digit, 2.5 inch, 7 segment super bright red LEDHH:MM:SS
AI-CL2-S1-FLPFlameproof slave clock4 digit, 2.5 inch, 7 segment super bright red LEDHH:MM

All three offer wired RS-485, wireless RF, and Ethernet TCP/IP with PoE communication, wall mounting, and a flameproof enclosure certified by CIMFR, Dhanbad.

Why a Flameproof Clock

Made so the clock cannot ignite the gas around it

A certified enclosure for the gas group

Electrical equipment in a classified area must be designed so that it cannot ignite the surrounding gas. A flameproof enclosure does that, and it has to be certified for the gas groups of the area. These clocks use enclosures certified by CIMFR, Dhanbad, for Gas Group Areas I, II, IIA, and IIB, so staff in those areas can read a synchronized time without a risk from the equipment.

Certification covers the enclosure, so the installation still has to follow the applicable requirements and use certified cable entry accessories.

Certified by CIMFR, Dhanbad

Gas Group Areas

IGas Group
IIGas Group
IIAGas Group
IIBGas Group
Flameproof enclosure on all three models
Customized to Your Requirements

Built around what your project needs

We build the clocks around what your project needs. You can choose the options on the right.

Tell us how many clocks you need, the area classification, and how far away people will read them, and our team will propose the configuration. Talk to our team

Display size
2.5 inch, or 4 inch for a larger, more visible display
Display format
Time only, or date and time
Time format
24 hour as standard, 12 hour on request
Time display
Hours and minutes (HH:MM), or hours, minutes, and seconds (HH:MM:SS)
Communication
Wired RS-485, wireless RF, or Ethernet TCP/IP with PoE
Power
24 VDC as standard, 230 VAC as an option
A 4 inch flameproof clock with large red LED digits

4 inch display

A bigger display for long viewing distances, customized to your requirements.

A flameproof clock showing the time and the date on two rows of red LED digits

Date and time format

Available when you want the date as well as the time.

Features

Built for hazardous areas

Flameproof Enclosure

Certified by CIMFR, Dhanbad, for use in Gas Group Areas I, II, IIA, and IIB

GPS Time from the Master

Satellite time, accurate to 500 milliseconds

Three Ways to Reach the Slaves

Wired RS-485, wireless RF, or Ethernet TCP/IP with PoE

Super Bright 2.5 Inch LED Display

A red 7 segment display that is easy to read across a work area

Larger 4 Inch Option

A bigger display for long viewing distances, customized to your requirements

Date and Time Format

Available when you want the date as well as the time

Memory Battery Backup

Keeps the real time clock running during power or communication failures

24 or 12 Hour Format

24 hour as standard, 12 hour on request

Wireless Mesh Network

Slaves can be up to 1.2 kilometers from the master

Wall Mounting

With model specific enclosure dimensions

Need something different?

Tell us the size, format, and communication you want, and we will configure it.

Talk to our team
Applications

Where the flameproof clocks are used

Pharmaceutical Manufacturing Facilities

Gives rooms with solvent handling and other classified zones the same time as the rest of the plant

Chemical Processing Plants

Keeps clocks in areas with flammable vapors on one time reference

Oil and Gas Installations

Provides a common, certified time display across plants and process areas

Industrial Production Areas

Gives production halls with explosion risk a uniform time for shift changes and process timing

Hazardous Area Manufacturing Facilities

Supplies a certified clock wherever a standard instrument would not be permitted

Other Locations Needing a Certified Flameproof Clock

Covers any area where the classification requires flameproof equipment

Choosing the Communication Method

Wired, wireless, or over your network

MethodHow it worksChoose it when
Wired RS-485
One master connects to up to 108 slave clocks over a wired networkYou can run cable through the area, and you want a fixed installation
Wireless RF
A mesh network at 865 MHz, with up to 255 slave clocks per master and slaves up to 1.2 km from the masterRunning cable through a hazardous area is difficult, or the clocks are spread across a large site
Ethernet TCP/IP with PoE
The clocks work on TCP over IP, and server time is synchronized across the networkYou already have network cabling and want your own server time on the clocks

The right method depends on the number of clocks, the layout, and the wiring available.

The GPS Receiver in the Master Clock

An active antenna that starts quickly

Active antenna, NMEA protocol

The master clock has an active GPS antenna with a 3 m cable, and it uses the NMEA protocol. A cold start takes about 45 seconds on average, a warm start about 45 seconds, and a hot start about 2 seconds.

45 sCOLD START
45 sWARM START
2 sHOT START

Place the antenna where it has a clear view of the sky, within reach of the 3 m cable, and check that the antenna location and its cable route are suitable for the area.

Active GPS antenna, 3 m cable
The AI-GPS-W-M2-FLP master clock with its active GPS antenna on a 3 m cable.
Mounting and Power

Wall mounted, on 24 VDC or 230 VAC

Mounting and installation

All clocks are wall mounted. Install them with suitable mounting arrangements and certified cable entry accessories, following the applicable certification and safety requirements.

Power supply

The standard supply for the 2.5 inch clocks is 24 VDC at 1 A, and a 230 VAC single phase, 50/60 Hz supply is optional.

24 VDCSTANDARD, 1 A
230 VACOPTIONAL, 50/60 HZ

The enclosure sizes for the 2.5 inch clocks are:

AI-GPS-W-M2-FLP and AI-CL2-S-FLP
Body 460 x 260 x 120 mm (W x H x D)
AI-CL2-S1-FLP
Body 340 x 170 x 90 mm (W x H x D)

Dimensions for 4 inch and date and time clocks depend on the configuration, so ask our team.

Specifications

Technical specifications

Parameter
Specification
Models (2.5 inch series)
AI-GPS-W-M2-FLP (GPS master), AI-CL2-S-FLP (slave, HH:MM:SS), AI-CL2-S1-FLP (slave, HH:MM)
Display Size
2.5 inch standard series; 4 inch available, customized to requirements
Display Format
Time (HH:MM:SS or HH:MM); date and time format available
Display
Master and AI-CL2-S-FLP: 6 digit, 7 segment super bright red LED, 2.5 inch, HH:MM:SS
AI-CL2-S1-FLP: 4 digit, 7 segment super bright red LED, 2.5 inch, HH:MM
GPS Receiver of Master
Active antenna, 3 m wire, NMEA protocol
Cold start 45 s (avg), warm start 45 s (avg), hot start 2 s
Communication
Wired RS-485 proprietary protocol for up to 108 clocks
Optional wireless RF at 865 MHz for up to 255 slave clocks in mesh topology
Ethernet TCP/IP with PoE
Wireless Range
Slaves up to 1.2 km (1,200 m) from the master
Accuracy
Master GPS time accurate to 500 ms
Standard GPS accuracy of ±1 second relayed across the network
Without a GPS signal, ±120 seconds per year standalone accuracy
Time Programming
GPS time from the master relayed across the wired or wireless network; keypad on the PCB inside the box, or optional wireless remote control
Time Display
24 hour standard; 12 hour on request
Input Supply
Standard 24 VDC, 1 A for 2.5 inch clocks
Optional 230 VAC single phase, 50/60 Hz
Battery Backup
Internal memory battery for real time clock backup in case of power or communication failure
Dimensions (W x H x D)
AI-GPS-W-M2-FLP and AI-CL2-S-FLP: body 460 x 260 x 120 mm
AI-CL2-S1-FLP: body 340 x 170 x 90 mm
Mounting
Wall mounted
Enclosure
Flameproof enclosure certified by CIMFR, Dhanbad, for use in areas of Gas Groups I, II, IIA, and IIB
Maintenance

Light upkeep

Clocks need little attention. Compare a slave with the master as part of routine checks, make sure the GPS antenna still has a clear view of the sky, and follow your quality and hazardous area procedures for checking and resetting clocks after a power or communication event. Do not open the enclosures in a classified area unless your site procedures allow it. Ask our team about the memory battery and its replacement interval.

Compliance

Certified enclosure, uniform time

The enclosures of the flameproof GPS clocks are certified by CIMFR, Dhanbad, for Gas Group Areas I, II, IIA, and IIB. That describes the enclosures, and it does not approve an installation, which depends on your hazardous area classification and on certified cable entry accessories.

Uniform time across a facility supports good time management practice, and the clocks assist your documentation by making sure that every area shows the same time. They do not create or store records, and they do not replace the time controls of your computerized systems or your validation work. Ace Instruments manufactures under an ISO 9001:2015 certified quality management system.

FAQs

Frequently asked questions

1. What are flameproof digital clocks?

Flameproof digital clocks are designed for industrial and hazardous area environments where suitable flameproof equipment is required. They provide a clear digital time display and help maintain a common time reference across different areas of a facility.

2. Why are flameproof clocks used in industrial environments?

In certain industrial areas, electrical equipment must meet specific hazardous area protection requirements. Flameproof clocks are designed with certified enclosures for the specified gas groups, allowing time information to be displayed in designated hazardous locations when installed according to applicable requirements.

3. Are GPS synchronized flameproof clocks available?

Yes. GPS synchronized flameproof clocks use a GPS master clock to receive accurate time from satellites and distribute it to connected slave clocks. This helps maintain consistent time across multiple locations in a facility.

4. What is the difference between a GPS master clock and a slave clock?

The GPS master clock receives time information from GPS satellites and distributes it to the slave clocks. Slave clocks receive this information and display the synchronized time, eliminating the need to adjust each clock individually.

5. Which flameproof clock models are available?

The 2.5 inch flameproof GPS clock catalogue includes three models:

  • AI-GPS-W-M2-FLP: GPS Master Clock with HH:MM:SS display.
  • AI-CL2-S-FLP: Slave Clock with HH:MM:SS display.
  • AI-CL2-S1-FLP: Slave Clock with HH:MM display.

Other clock sizes and display configurations, including 4 inch clocks and date and time display options, are also available in the product range. Please confirm the required model and configuration with the technical team.

6. What display sizes are available for flameproof clocks?

The catalogue covers 2.5 inch high, super bright red LED displays. We also offer 4 inch clock options for applications requiring a larger, more visible display. The suitable size depends on viewing distance and installation requirements.

7. Can the clocks display both date and time?

Date and time display options are available in our clock range, depending on the selected model and configuration. Customers requiring both date and time should specify this requirement when requesting a quotation so the appropriate model can be recommended.

8. What time formats are available?

The flameproof GPS clock catalogue includes the following display formats:

  • HH:MM:SS: Hours, minutes, and seconds.
  • HH:MM: Hours and minutes.

The standard format is 24 hour time. A 12 hour format can also be provided on request.

9. How does GPS synchronization work?

The GPS master clock receives time information through an active GPS antenna. It then distributes the synchronized time to connected slave clocks through the selected communication arrangement. This helps maintain a consistent time display throughout the facility.

10. What communication options are available?

The flameproof GPS clock series supports three communication options:

  • Wired RS-485 communication.
  • Wireless RF communication at 865 MHz.
  • Ethernet TCP/IP communication with an optional PoE arrangement.

The appropriate option depends on the facility layout, number of clocks, wiring availability, and network requirements.

11. How many slave clocks can be connected to one master clock?

Up to 108 slave clocks can be connected to one master clock through wired RS-485 communication. With wireless RF communication in a mesh network, up to 255 slave clocks can be connected to one master clock. Confirm the final network capacity with the technical team for your selected configuration.

12. What happens if GPS communication or the power supply is interrupted?

The clocks include an internal memory battery for real time clock backup during power or communication failures. The catalogue specifies standalone accuracy of approximately ±120 seconds per year in the absence of GPS synchronization. Normal synchronization resumes when the relevant signal or communication is restored.

13. What is the accuracy of the flameproof GPS clock system?

The catalogue specifies GPS receiver accuracy of approximately 500 milliseconds and standard time accuracy of ±1 second when time is relayed across the network. This helps maintain a consistent time reference across connected clocks.

14. What type of enclosure is used in the flameproof clocks?

The catalogue specifies a flameproof enclosure certified by CIMFR, Dhanbad, for use in areas classified under gas groups I, II, IIA, and IIB. The enclosure is intended for the specified hazardous area applications and must be installed according to the applicable certification and safety requirements.

15. Where can flameproof clocks be installed?

Flameproof clocks can be considered for suitable industrial and hazardous area applications, including:

  • Pharmaceutical manufacturing facilities
  • Chemical processing plants
  • Oil and gas installations
  • Industrial production areas
  • Hazardous area manufacturing facilities
  • Other locations requiring certified flameproof clock enclosures

The suitability of a particular model depends on the area’s classification and the equipment certification.

16. What power supply options are available?

The catalogue specifies a standard 24 VDC, 1 A supply for the 2.5 inch clocks. An optional 230 VAC single phase, 50/60 Hz supply is also available. The supply should be selected according to the ordered configuration.

17. How are flameproof clocks mounted?

The clocks are designed for wall mounting. The catalogue provides model specific enclosure dimensions for the master and slave clocks. Installation should be carried out using suitable mounting arrangements and certified cable entry accessories.

18. How can I select the right flameproof clock for my facility?

When selecting a clock, consider the display size (2.5 inch or 4 inch), whether you require time only or date and time display, the number of clock locations, master and slave arrangement, communication method, power supply, and hazardous area classification. Share these requirements with the technical team to identify the appropriate configuration.

19. Can the flameproof clocks be customized?

Yes. We customize the clocks according to the client’s requirements. You can choose a 2.5 inch or a 4 inch display, time only or date and time format, 24 hour or 12 hour time, the communication method, and the power arrangement. Share your requirements and your area classification with our team, and they will propose a configuration.

20. How can I request a quotation or technical assistance for flameproof clocks?

For help selecting master and slave clocks, display size, communication options, and power arrangements, or for project specific requirements, contact the Cleanroom Monitors team through the contact page. Please share the number of clock locations, preferred display size and format, the hazardous area classification, and the installation layout.

Need help choosing?

Tell us how many clocks you need, the area classification, and how far away people will read them, and our team will propose the configuration.

Request a quote

Exceptional Instruments That Surpass Your Technical Expectations

Powerful, customized solutions to suit your unique cleanroom monitoring needs

Discover more
No items found.
Download Specifications

Gain insight into your IAQ solution and know technical specifications

Learn more
Know the capabilities of the latest in cleanroom monitoring technology, watch or download PDF for insight
Check our YoutubeDownload Brochure (PDF)

Exceptional Instruments That Surpass Your Technical Expectations

Powerful, customized solutions to suit your unique cleanroom monitoring needs

Discover more